ElectraStim Flick Stimulator Multi-Pack

The ElectraStim Flick Stimulator Multi-Pack - EM60-M includes 3 accessories, an ElectraStim Flick single-channel stimulator an Aura Silicone Probe, some conductive pads and all of the necessary wires and charger to play right away.

Our rechargeable ElectraStim Flick EM60 Stimulator has a single stimulation channel, 7 stimulating patterns, 24 intensities and a revolutionary motion-sympathetic Flick Mode, offering an array of thrilling stimulation settings to experience.

• Rechargeable via USB - no batteries required
• Up to 6 hours Use between charges
• Low battery indicator
• Easy to use, even for beginners
• Intensified pleasure during all sexual activities
• Ideal for masturbation, foreplay or as a couple's sex toy during penetrative sex
• 7 stimulation settings including continuous stimulation, pulsation and escalation
• 24 intensity levels
• Soft-touch control unit with push buttons and LED display
• Small size
• Built to the highest standards

Dimensions:

95mm x 55mm x 15mm (approximately 3.74 inches x 2.25 inches x 0.75 inches) 

What is included?

• 1x ElectraStim Flick EM60 Stimulator
• 1x Bi-Polar Silicone Noir Aura Multi Probe
• 2x Uni-Polar ElectraLoops Electro Cock Rings
• 4x Uni-Polar ElectraPads
• 1x Tube of Electro-Conductive Gel
• 1x Premium Lubricant Sample
• 1x Connecting wire with 2mm pin connectors
• 1x Charging cable
• 1x Storage pouch

How to use the EM60:

How To Charge Your EM60 'Flick' Stimulator
Connect the included charging cable to your Flick stimulator, plug it into any USB port or a plug adapter and allow it to fully charge. A red light will illuminate while the stimulator is charging and will switch off once charging is complete. A full charge will take up to 3 hours.

How To Set Up Your 'Flick' Stimulator
Once the stimulator is charged, it’s time for the fun to start! Simply insert the connecting wire into the top of your stimulator and insert both 2mm on the ends into your chosen electrode/s.

It’s also possible to share sensation with a partner when you each use a toy connected to the same wire.

How To Use The EM60 'Flick'

Changing Power Levels
Switch on your EM60 by pressing the on/off button. The display will illuminate to let you know the unit is active. The intensity level will be set to 0 and the stimulation will be on a continuous setting.

Increase the power level by pressing the intensity up button and you will begin to feel stimulation. Every press will increase the stimulation intensity by one level and you may need to climb a few levels before you notice the sensations. If you do not feel any stimulation, switch the stimulator off and reconnect the pins, ensuring they are inserted all the way into your chosen electrode/s and try again.
There are 24 intensity levels to cater for all tastes, so you’ll find the right setting for you with a little experimentation. If stimulation feels too intense, press the intensity down button or press the on/off button to switch the unit off. When you power the stimulator up again, intensity will be reset to 0.

The intensity level display has 12 lights that illuminate at 3 different brightnesses to tell you which intensity level has been selected.

Changing Patterns
Each press of the mode button will change the stimulation pattern.
There are 7 settings in total and the stimulator will always start with the continuous setting. Each press of the mode button will activate a new pattern setting:

Continuous – Smooth and constant
Wave – Slow and gentle waves / massage effect
Escalating Wave – Alternating fast and slow waves
Slow Pulse – Pulsating
Dual Pulse – Medium burst followed by fast bursts
Falling Rest – Pulsing pattern with an ever-decreasing
rest period until the stimulation is constant (repeats)
Escalating Pulse – Slow pulse escalating to a fast pulse and then slowing again
The output activity LED monitor will flash an orange LED light in time with stimulation so you know which pattern setting is selected.

Activating the 'Flick' mode
Hold the mode button down for two seconds and you’ll activate our revolutionary Flick mode. This specialist setting allows you to enjoy stimulation that reacts to your movements, creating tailor-made patterns.

How To Use The Flick Mode
Hold the stimulator flat and use up-and-down motions to shake it similarly to how you might shake a maraca. The harder and faster you shake, the more intense and quicker stimulation will feel. You can adjust the intensity levels just like you can with any of the other stimulation modes so it will never feel too strong.
The Flick LED display will show you the intensity of each motion. When you are reaching your maximum selected intensity, it will show four green lights and one red light at the very top. To increase intensity further, simply press the intensity up button.

Sharing sensations with a partner
You and your partner can share sensations with ElectraStim Flick when you both use an electrode connected to the same stimulator. Connect your electrodes as normal but instead of one person using both electrodes, you’ll each take charge of your own electrode. You can use any combination of electrodes to complement your individual tastes.
Once your electrodes are in place, you should get into position and make sure your bodies are touching below the waist before you switch the stimulator on. Slowly increase the intensity to a level you’re both happy with as you will both experience the same intensity. During play you’ll both experience sensation through your chosen electrodes but you’ll also feel those erotic tingles everywhere you touch one another for a truly synchronised sexual experience.